QUESTION NO: 1
From which resource would you obtain the VNX Block recovery document?
From which resource would you obtain the VNX Block recovery document?
Correct Answer: A
Vote an answer
QUESTION NO: 2
Which resource is required for all VNX activities performed by EMC and Partner personnel?
Which resource is required for all VNX activities performed by EMC and Partner personnel?
Correct Answer: B
Vote an answer
QUESTION NO: 3
Which will be displayed by running the df command on the primary Control Station?
Which will be displayed by running the df command on the primary Control Station?
Correct Answer: C
Vote an answer
QUESTION NO: 4
After a new VNX 5400 was installed and powered up, the Data Movers are continuously rebooting. It has been determined that a cabling issue is at fault.
Which configuration should be checked first as the most likely cause?
After a new VNX 5400 was installed and powered up, the Data Movers are continuously rebooting. It has been determined that a cabling issue is at fault.
Which configuration should be checked first as the most likely cause?
Correct Answer: C
Vote an answer
QUESTION NO: 5
You are onsite for a DAE and drive upgrade for a VNX 5800 array. After inspecting the collections from the array you notice that the VNX has the following active configuration: 1 x 2.5" DPE 21 x 2.5" DAE's 10 x 3.5" DAE's 681 bound data and hotspare drives 0 faulted drives 2 unbound drives
How many additional 2.5" DAEs and drives can the array support?
You are onsite for a DAE and drive upgrade for a VNX 5800 array. After inspecting the collections from the array you notice that the VNX has the following active configuration: 1 x 2.5" DPE 21 x 2.5" DAE's 10 x 3.5" DAE's 681 bound data and hotspare drives 0 faulted drives 2 unbound drives
How many additional 2.5" DAEs and drives can the array support?
Correct Answer: C
Vote an answer
QUESTION NO: 6
What is used to determine the source of an issue, its symptoms and actions to resolve the issue?
What is used to determine the source of an issue, its symptoms and actions to resolve the issue?
Correct Answer: C
Vote an answer
QUESTION NO: 7
When installing a VNX for File, which subnet must be used?
When installing a VNX for File, which subnet must be used?
Correct Answer: B
Vote an answer
QUESTION NO: 8
On a VNX, SPA is unavailable through Unisphere and does not respond to a ping. The engineer observes an amber light on the front of the SP. What is the state of the SP and what corrective action should be taken?
On a VNX, SPA is unavailable through Unisphere and does not respond to a ping. The engineer observes an amber light on the front of the SP. What is the state of the SP and what corrective action should be taken?
Correct Answer: B
Vote an answer
QUESTION NO: 9
Which condition indicates an SP is in degraded mode?
Which condition indicates an SP is in degraded mode?
Correct Answer: C
Vote an answer
QUESTION NO: 10
You are working on a VNX Unified system that has a fault LED illuminated on the DME. What action would you take to further analyze the system status?
You are working on a VNX Unified system that has a fault LED illuminated on the DME. What action would you take to further analyze the system status?
Correct Answer: B
Vote an answer
QUESTION NO: 11
Refer to the exhibit.
From the highlighted information in the picture, which type of I/O module is represented?
Refer to the exhibit.
From the highlighted information in the picture, which type of I/O module is represented?
Correct Answer: B
Vote an answer
QUESTION NO: 12
You are required to install ESRS on a newly installed VNX for Block array. Where can the latest version of the VNX Installation Toolbox be located?
You are required to install ESRS on a newly installed VNX for Block array. Where can the latest version of the VNX Installation Toolbox be located?
Correct Answer: B
Vote an answer
QUESTION NO: 13
During a VNX gateway manual installation you are registering Data Mover initiators on the VNX Block back-end array. Which 8-byte WWN is the initiator for Data Mover 2 HBA 1?
During a VNX gateway manual installation you are registering Data Mover initiators on the VNX Block back-end array. Which 8-byte WWN is the initiator for Data Mover 2 HBA 1?
Correct Answer: D
Vote an answer