HP Aruba Certified Switching Associate - HPE6-A72 Free Exam Questions [2026]

QUESTION NO: 1
What is the correct description of a Multi-Layer Switch?

A. has all the functionality of a Layer 2 switch and most of the functionality of a Layer 3 router

B. any switch that supports PoE, LLDP-MED and Flow Control

C. multi-Layer refers specifically to using chassis switches with several line cards over stack port switches

D. a switch with Layer 3 routing capabilities but lacks any Layer 1 features as a consequence

Discussion 0

Correct Answer: A Vote an answer

QUESTION NO: 2
Which two options are the Layer 2 protocols? (Choose two.)

A. STP

B. RIP

C. 802.1Q

D. IPSec

E. 802.11af

Discussion 0

Correct Answer: A,C Vote an answer

QUESTION NO: 3
You need to remote into an AOS-CX switch using SSH in order to update the management IP address for future connections. Unfortunately, you mis-configured the IP address and are now locked out of the switch.
What command could you have issued before making changes that would have recovered the original switch configuration after ten minutes?

A. checkpoint auto confirm 10

B. checkpoint rollback 10

C. checkpoint auto 10

D. boot system secondary 10

Discussion 0

Correct Answer: C Vote an answer

QUESTION NO: 4
Refer to the exhibit

What is true regarding VLAN 50 according to the diagram above?

A. VLAN 50 is part of a switched virtual interface (SVI) that was never routed causing it to be down.

B. VLAN 50 was never added to the vlan-database and therefore is in a down state.

C. Since VLAN 50 has not been assigned to any enabled physical port, the status is down.

D. VLAN 50 is assigned only to Trunk ports which is why no ports are listed under interfaces.

Discussion 0

Correct Answer: C Vote an answer

QUESTION NO: 5
Refer to the exhibit.

You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master. What is a valid configuration for Access-2 to join the VSF stack?

A. Access-2# configure
Access-2(config)# vsf member 1
Access-2(vsf-member-1)# link 1 1/1/28
Access-2(vsf-member-1)# exit
Access-2(config)# vsf renumber-to 2
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

B. Access-2# configure
Access-2(config)# vsf member 1
Access-2(config)# vsf renumber-to 2
Access-2(vsf-member-1)# link 2 2/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

C. Access-2# configure
Access-2(config># vsf member 2
Access-2(vsf-member-1)# link 2 1/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

D. Access-2# configure
Access-2(config)# vsf member 2
Access-2(vsf-member-1)# link 1 1/1/28
Access-2(vsf-member-1)# exit
This will save the VSF configuration and reboot the switch.
Do you want to continue (y/n)? y

Discussion 0

Correct Answer: D Vote an answer

QUESTION NO: 6
Refer to the exhibit.

Which command produces the above output?

A. show interface port 1/1/10 switchport

B. show interface port 1/1/10 trunk

C. show vlan port 1/1/10

D. show trunk port 1/1/10 extended

Discussion 0

Correct Answer: D Vote an answer

QUESTION NO: 7
Which two port characteristics must match between LAG interfaces? (Choose two.)

A. Media type

B. Chassis number

C. Member ID

D. Duplex

E. Port number

Discussion 0

Correct Answer: A,D Vote an answer

QUESTION NO: 8
What are two features of the three-tier designs? (Choose two.)

A. removes the distribution layer in favor of a spine-leaf design used in modern data center deployments

B. uses only Layer 2 access on the Access and the Core with Layer 3 routing and access control provided at the distribution layer

C. a more scalable design over by leveraging a distribution layer to handle Layer 3 routing and access control in large deployments

D. is considered legacy by requiring a large flat layer-two broadcast domain from Core to Access and should be avoided

E. adds a distribution layer to free up resources from the Core for improved performance and routing throughput

Discussion 0

Correct Answer: C,E Vote an answer

QUESTION NO: 9
Core(config)# user admin password
Core(config)# interface mgmt
Core(config-if-mgmt)# ip static 10.254.16.89/22
Core(config-if-mgmt)# default-gateway 10.254.19.129
Core(config)# ssh server vrf mgmt
Core(config)# https-server vrf mgmt
You are tasked with configuring the Core switch to be managed by NetEdit. Currently, the Core switch is at factory-default settings.
Which two steps are missing? (Choose two.)

A. Core(config-if-mgmt)# no shutdown

B. Core(config-if-mgmt)# enable

C. Core(config)# https-server rest access-mode read-only

D. Core(config)# https-server rest access-mode read-write

E. Core(config-if-mgmt)# no tftp-server

Discussion 0

Correct Answer: A,D Vote an answer

QUESTION NO: 10
Which port or ports should be allowed through a firewall so that an AOS-CX switch can act as an SNMP Agent?

A. UDP 1812 and UDP 1813

B. UDP 161

C. TCP 443

D. UDP 162

Discussion 0

Correct Answer: B Vote an answer

QUALITY AND VALUE

Tested and Approved

Easy to Pass

Try Before Buy

RECENT DISCUSSIONS

Useful Links

Contact Us