QUESTION NO: 1
An administrator has a FlexPod solution using VMware vSphere 6.0. The ESXi hosts use iSCSI for storage connectivity, and all paths have been configured and connected between the NetApp cluster and the ESXi hosts.
Virtual Storage Console has been installed and ESXi host-recommended settings have been applied to all hosts. The active LUN path for one of the iSCSI datastores experiences a connectivity failure and the LUN switches to a new active path.
In this scenario, which event would trigger the ESXi host to switch the active LUN path again?
An administrator has a FlexPod solution using VMware vSphere 6.0. The ESXi hosts use iSCSI for storage connectivity, and all paths have been configured and connected between the NetApp cluster and the ESXi hosts.
Virtual Storage Console has been installed and ESXi host-recommended settings have been applied to all hosts. The active LUN path for one of the iSCSI datastores experiences a connectivity failure and the LUN switches to a new active path.
In this scenario, which event would trigger the ESXi host to switch the active LUN path again?
Correct Answer: B
Vote an answer
QUESTION NO: 2
Given the following switch output, where would you expect see notification level messages?
N5K-1# show logging info.
Logging console: enabled (Severity: error)
Logging monitor: enabled (Severity: informational)
Logging linecard: enabled (Severity: emergency)
Logging fex: enabled (Severity: notifications)
Logging time stamp: seconds
Logging server: disabled
Logging logfile: enabled
Given the following switch output, where would you expect see notification level messages?
N5K-1# show logging info.
Logging console: enabled (Severity: error)
Logging monitor: enabled (Severity: informational)
Logging linecard: enabled (Severity: emergency)
Logging fex: enabled (Severity: notifications)
Logging time stamp: seconds
Logging server: disabled
Logging logfile: enabled
Correct Answer: B
Vote an answer
QUESTION NO: 3
Which three actions are required to configure two Cisco Nexus switches as vPC peers? (Choose three.)
Which three actions are required to configure two Cisco Nexus switches as vPC peers? (Choose three.)
Correct Answer: A,C,D
Vote an answer
QUESTION NO: 4
A Cisco UCS system is operating in FC End-Host Mode. The fabric Interconnects are uplinked into Nexus 5672UP switches using native FC. The service profiles are unable to boot from SAN using FC.
When executing the show flogi database command on the Nexus switches, only the Fabric Interconnect port WWNs are visible. No service profile WWNs are shown.
What caused this issue?
A Cisco UCS system is operating in FC End-Host Mode. The fabric Interconnects are uplinked into Nexus 5672UP switches using native FC. The service profiles are unable to boot from SAN using FC.
When executing the show flogi database command on the Nexus switches, only the Fabric Interconnect port WWNs are visible. No service profile WWNs are shown.
What caused this issue?
Correct Answer: B
Vote an answer
QUESTION NO: 5
Exhibit:
Your vSphere host is booting off an SD and is displaying the error shown in the exhibit.
What should you do to correct the problem?
Exhibit:
Your vSphere host is booting off an SD and is displaying the error shown in the exhibit.
What should you do to correct the problem?
Correct Answer: A
Vote an answer
QUESTION NO: 6
After deploying a FlexPod solution, which tool would you use to validate a successful installation?
After deploying a FlexPod solution, which tool would you use to validate a successful installation?
Correct Answer: A
Vote an answer
QUESTION NO: 7
When trying to configure a Virtual Port Channel (vPC), what might be a cause of the following error when trying to create the vPC domain?
Nexus-5548-B(config)# vpc domain 10
^% Invalid command at '^' marker.Nexus-5548-B(config)#
When trying to configure a Virtual Port Channel (vPC), what might be a cause of the following error when trying to create the vPC domain?
Nexus-5548-B(config)# vpc domain 10
^% Invalid command at '^' marker.Nexus-5548-B(config)#
Correct Answer: B
Vote an answer
QUESTION NO: 8
What is the correct flow control setting for the intercluster ports on a NetApp cluster?
to 50% cashback.
What is the correct flow control setting for the intercluster ports on a NetApp cluster?
to 50% cashback.
Correct Answer: C
Vote an answer
QUESTION NO: 9
What aggregate containing the root volume is created during the Clustered Data ONTAP setup process?
What aggregate containing the root volume is created during the Clustered Data ONTAP setup process?
Correct Answer: A
Vote an answer