Cisco Meraki Solutions Specialist 500-220 Real Exam Questions and Answers FREE Updated on Jun 19, 2022
500-220 Ultimate Study Guide - Actual4test
Cisco 500-220 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
| Topic 7 |
|
NEW QUESTION 21
Where should a network admin navigate to investigate wireless mesh information between Meraki APs?
- A. Wireless > Configure > Radio Settings
- B. Wireless > Monitor > RF Spectrum
- C. Wireless > Monitor > Access Points > AP > RF
- D. Wireless > Monitor > Wireless Health
Answer: C
NEW QUESTION 22
When an SSID is configured with Sign-On Splash page enabled, which two settings must be configured for unauthenticated clients to have full network access and not be allow listed? (Choose two.)
- A. Simultaneous logins
- B. Controller disconnection behavior
- C. Captive Portal strength
- D. Firewall & traffic shaping
- E. RADIUS for splash page settings
Answer: B,C
NEW QUESTION 23
Refer to the exhibit.
Which design recommendation should be considered?
- A. A 50-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 1-hop maximum.
- B. A 50-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 2-hop maximum.
- C. A 25-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 1-hop maximum.
- D. A 25-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 2-hop maximum.
Answer: C
NEW QUESTION 24
What is a feature of distributed Layer 3 roaming?
- A. All wireless client traffic is tunneled.
- B. An MX Security Appliance is required as a concentrator.
- C. An MX Security Appliance is not required as a concentrator.
- D. All wireless client traffic can be split-tunneled.
Answer: C
Explanation:
Reference:
Cisco_Meraki_Best_Practice_Design/Best_Practice_Design_-_MR_Wireless/
Wireless_Layer_3_Roaming_Best_Practices
NEW QUESTION 25
What are two roles of the network and device tags in a Dashboard? (Choose two.)
- A. Network tags can be used to assign networks to separate Auto VPN domains in an Organization with many networks.
- B. Network tags can be used to simplify the assignment of network-level permissions in an Organization with many networks.
- C. Device tags can be used to simplify the assignment of device-level permissions in an Organization with many administrators.
- D. Tags enable administrators to configure a combination of network and device specific tags to create summary reports filtered for specific devices across multiple networks.
- E. Device tags can be assigned to MR APs to influence the gateway selection for repeaters in a mesh wireless network.
Answer: D,E
Explanation:
Reference:
Organization_Menu/Manage_Tags
NEW QUESTION 26
Which two Systems Manager Live tools are available only for Apple Macs and Windows PCs and cannot be used on iOS or Android mobile devices? (Choose two.)
- A. Selective wipe
- B. Remote Desktop
- C. Send notification
- D. OS updates
- E. Screenshot
Answer: A,B
NEW QUESTION 27
A customer wants to use Microsoft Azure to host corporate application servers.
Which feature does the customer get by using a vMX appliance rather than connecting directly to Azure by VPN?
- A. malware protection
- B. SD-WAN
- C. next-generation firewall
- D. intrusion prevention
Answer: C
NEW QUESTION 28
Which type of authentication protocol is used when using OSPF on an MX appliance?
- A. plaintext
- B. certificate
- C. MD5
- D. SHA-1
Answer: C
Explanation:
Reference:
Using_OSPF_to_Advertise_Remote_VPN_Subnets
NEW QUESTION 29
Drag and drop the settings from the left into the boxes on the right to indicate if the setting will be cloned or not cloned using the Cisco Meraki MS switch cloning feature.
Answer:
Explanation:
NEW QUESTION 30
Which design requirement is met by implementing syslog versus SNMP?
- A. when organization-wide information must be collected
- B. when automation capabilities are needed
- C. when information such as flows and client connectivity must be gathered
- D. when proactive alerts for critical events must be generated
Answer: C
Explanation:
Reference:
Meraki_Device_Reporting_-_Syslog%2C_SNMP%2C_and_API
NEW QUESTION 31
Drag and drop the descriptions from the left onto the corresponding MX operation mode on the right.
Answer:
Explanation:
NEW QUESTION 32
A new application needs to be pushed to all iOS devices. Some devices report "NotNow" in the event log and do not install the application.
What does the "NotNow" event indicate?
- A. The device is locked with a passcode.
- B. The application requires the most recent iOS version.
- C. The device cannot connect to Cisco Meraki servers.
- D. The device cannot connect to Apple servers.
Answer: A
NEW QUESTION 33
Refer to the exhibit.
Which IDS/IPS mode is the MX Security Appliance configured for?
- A. detection
- B. blocking
- C. prevention
- D. quarantine
Answer: C
NEW QUESTION 34
Refer to the exhibit.
The VPN concentrator is experiencing issues. Which action should be taken to ensure a stable environment?
- A. Configure the MX appliance to Routed mode on the Addressing & VLANS page.
- B. Physically disconnect all LAN ports.
- C. Remove the connection from Internet 1.
- D. Add a deny any/any firewall rule to the end of the firewall rules.
Answer: B
NEW QUESTION 35
Which configuration step is necessary when automatic updating is required of iOS apps provisioned through Systems Manager that are found in the App Store?
- A. No configuration step is necessary; automatic updating is the default behavior.
- B. Configure automatic updating of iOS devices in the Meraki installed profile.
- C. Create a security policy that enables automatic updates.
- D. Create a profile with automatic update enabled and apply it to iOS devices.
Answer: C
NEW QUESTION 36
What is the best practice Systems Manager enrollment method when deploying corporate-owned iOS devices?
- A. manual
- B. DEP
- C. Apple Configurator
- D. Sentry enrollment
Answer: C
NEW QUESTION 37
Which two primary metrics does Meraki Insight use to calculate the Application Performance Score? (Choose two.)
- A. Maximum Latency
- B. Maximum Jitter
- C. Per-flow Goodput
- D. Total Bandwidth Usage
- E. Application Response Time
Answer: C,E
NEW QUESTION 38
Which two features and functions are supported when using an MX appliance in Passthrough mode? (Choose two.)
- A. high availability
- B. site-to-site VPN
- C. DHCP
- D. secondary uplinks
- E. intrusion prevention
Answer: B,E
Explanation:
Reference:
Passthrough_Mode_on_the_MX_Security_Appliance_and_Z-series_Teleworker_Gateway
NEW QUESTION 39
A customer requires a hub-and-spoke Auto VPN deployment with two NAT-mode hubs with dual uplink connections and 50 remote sites with a single uplink connection.
How many tunnels does each hub need to support?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 40
......
Ultimate Guide to Prepare 500-220 Certification Exam for Cisco Meraki Solutions Specialist: https://www.actual4test.com/500-220_examcollection.html
Use Real 500-220 Dumps - Cisco Correct Answers: https://drive.google.com/open?id=17nGIz_C6-_uVBXKyV6WFnxrGC1rgA7s6