Here are all the actual test exam dumps for IT exams. Most people prepare for the actual exams with our test dumps to pass their exams. So it's critical to choose and actual test pdf to succeed.

[Sep 29, 2026] Latest CWNP CWNA-109 Exam Practice Test To Gain Brilliante Result [Q24-Q44]

Share

Latest [Sep 29, 2026] CWNP CWNA-109 Exam Practice Test To Gain Brilliante Result

Take a Leap Forward in Your Career by Earning CWNP CWNA-109


CWNP CWNA-109 Exam Syllabus Topics:

TopicDetails
Topic 1
  • WLAN Protocols and Devices: It focuses on terminology related to the 802.11 MAC and PHY, the purpose of the three main 802.11 frame types, MAC frame format, and 802.11 channel access methods.
Topic 2
  • Radio Frequency (RF) Technologies: This topic explains the basic features and behavior of RF. It also discusses applying the basic concepts of RF mathematics and measurement. Lastly, the topic covers RF signal characteristics and the functionality of RF antennas.
Topic 3
  • RF Validation and WLAN remediation: This topic covers RF interference, WLAN performance, the basic features of validation tools, and common wireless issues.
Topic 4
  • WLAN Regulations and Standards: The topic discusses the roles of WLAN and networking industry organizations. It also addresses the concepts of various Physical Layer (PHY) solutions, spread spectrum technologies, and 802.11 WLAN functional concepts.

 

NEW QUESTION # 24
An 802.11-based network uses an AP and has several connecting clients. The clients include iPhones, iPads, laptops and one desktop. What WLAN use case is represented?

  • A. BSS
  • B. IBSS
  • C. Ad-hoc
  • D. WPAN

Answer: A

Explanation:
A BSS (Basic Service Set) is a WLAN use case that represents an 802.11-based network that uses an AP (Access Point) and has several connecting clients. The AP acts as a central point of coordination and communication for the clients, which can include iPhones, iPads, laptops, desktops, or any other devices that have Wi-Fi capabilities. A BSS can be identified by a unique BSSID (Basic Service Set Identifier), which is usually the MAC address of the AP's radio interface. A BSS can also be associated with an SSID (Service Set Identifier), which is a human-readable name that identifies the network. References: , Chapter 1, page 23; , Section 1.1


NEW QUESTION # 25
A POE device requires 47 W of power. What POE specification should be used?

  • A. 802.3af
  • B. 802. 11at
  • C. 802.3bt
  • D. 802.3at

Answer: C

Explanation:
A POE device that requires 47 W of power should use the 802.3bt specification. This is because 802.3bt is the latest POE standard that supports up to 90 W of power delivery over four pairs of wires in an Ethernet cable.
The previous POE standards, such as 802.3af and 802.3at, only support up to 15.4 W and 30 W of power delivery over two pairs of wires in an Ethernet cable, respectively. Therefore, they are not sufficient for powering a device that requires 47 W of power. The 802.11at specification does not exist; it is a typo or confusion with the 802.3at specification. References: CWNA-109 Study Guide, Chapter 8: Wireless LAN Access Points, page 2431


NEW QUESTION # 26
What ID is typically mapped to an AP's MAC address if a single BSS is implemented?

  • A. VLAN ID
  • B. Device ID
  • C. BSSID
  • D. SSID

Answer: C

Explanation:
The BSSID (Basic Service Set Identifier) is typically mapped to an AP's MAC address if a single BSS is implemented. The BSSID is a unique identifier that distinguishes one BSS from another within the same RF medium. It is usually derived from the MAC address of the AP's radio interface, but it can also be manually configured or randomly generated by some vendors. The BSSID is used by client stations to associate with an AP and to send and receive frames within a BSS.


NEW QUESTION # 27
Your consulting firm has recently been hired to complete a site survey for a company desiring an indoor coverage WI-AN. Your engineers use predictive design software for the task, but the company insists on a pre- design site visit.
What task should be performed as part of the pre-design visit to prepare for a predictive design?

  • A. Evaluate the building materials at the facility and confirm that the floor plan documents are consistent with the actual building
  • B. Install at least one AP on each side of the exterior walls to test for co-channel interference through these walls
  • C. Collect information about the company's security requirements and the current configuration of their RADIUS and user database servers
  • D. Test several antenna types connected to the intended APS for use in the eventual deployment

Answer: A

Explanation:
A pre-design site visit in preparation for a predictive wireless LAN design is essential for gathering physical and environmental data about the site. The key tasks to be performed during such a visit include:
* Evaluating Building Materials: Different materials (concrete, glass, wood, etc.) have varying effects on RF signal propagation. Understanding the materials present helps in accurately predicting how signals will behave within the environment.
* Floor Plan Verification: Ensuring that the floor plan documents are an accurate representation of the actual building layout is crucial. Discrepancies between the floor plans and the physical layout can lead to inaccuracies in the predictive design.
The other options, while potentially valuable in other contexts, are not directly related to preparing for a predictive design:
* Installing APs (option A) for testing co-channel interference is more aligned with an active site survey rather than a pre-design visit for a predictive design.
* Collecting information about security requirements (option B) is important but is not directly related to the physical aspects of the site that would impact a predictive design.
* Testing antenna types (option C) would typically be part of an active site survey or the actual deployment phase, not a pre-design visit for predictive modeling.
Therefore, option D is the correct answer, focusing on evaluating physical aspects crucial for accurate predictive modeling.
References:
CWNA Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109, by David D.
Coleman and David A. Westcott.
Best practices for conducting pre-design site visits in wireless network planning.


NEW QUESTION # 28
You manage a WLAN with 100 802.11ac access points. All access points are configured to use 80 MHz channels. In a particular BSS, only 40 MHz communications are seen. What is the likely cause of this behavior?

  • A. The clients are all 802.11n STAs or lower
  • B. The short guard interval is also enabled
  • C. All clients implement single spatial stream radios
  • D. The AP is improperly configured to use only 40 MHz of the 80 MHz allocated bandwidth

Answer: A

Explanation:
https://7signal.com/802-11ac-migration-part-2-whats-nobodys-telling-you-about-80mhz-and-160mhz-channel- bonding The clients are all 802.11n STAs or lower is the likely cause of this behavior. If a WLAN with 100 802.11ac access points is configured to use 80 MHz channels, but only 40 MHz communications are seen in a particular BSS, it means that the clients in that BSS do not support 80 MHz channels. This could be because they are using older standards, such as 802.11n or lower, that do not support 80 MHz channels. Alternatively, they could be using newer standards, such as 802.11ac or ax, but have their channel width settings limited to 40 MHz or lower due to device capabilities or configuration options. In either case, the AP will adapt to the client's channel width and use only 40 MHz of the 80 MHz allocated bandwidth to communicate with them.
This will reduce the potential throughput and efficiency of the WLAN. References: , Chapter 3, page 111; , Section 3.2


NEW QUESTION # 29
You are troubleshooting a controller-based AP that is unable to locate the controller. DHCP is not use and the controller is located at 10.10.10.81/24 while the AP is on the 10.10.16.0/24 network. What should be inspected to verify proper configuration?

  • A. NTP
  • B. AP hosts file
  • C. DNS
  • D. BOOTH

Answer: C

Explanation:
What should be inspected to verify proper configuration is DNS. DNS stands for Domain Name System and is a service that resolves hostnames to IP addresses. In a controller-based AP deployment, DNS can be used to help the AP locate the controller by using a predefined hostname such as CISCO-CAPWAP-CONTROLLER or aruba-master. The AP sends a DNS query for this hostname and receives an IP address of the controller as a response. Therefore, if DNS is not configured properly or if there is no DNS entry for the controller hostname, the AP may not be able to locate the controller. NTP, BOOTP, and AP hosts file are not relevant for this scenario. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 374; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 364.


NEW QUESTION # 30
A client complains of low data rates on his computer. When you evaluate the situation, you see that the signal strength is -84 dBm and the noise floor is -96 dBm. The client is an 802.11ac client and connects to an 802.11 ac AP. Both the client and AP are 2x2:2 devices. What is the likely cause of the low data rate issue?

  • A. Too few spatial streams
  • B. Lack of support for 802.11n
  • C. Weak signal strength
  • D. CAT5e cabling run to the AP

Answer: C

Explanation:
Weak signal strength is the likely cause of the low data rate issue for the client that has a signal strength of
-84 dBm and a noise floor of -96 dBm. The client is an 802.11ac client and connects to an 802.11ac AP. Both the client and AP are 2x2:2 devices. Signal strength is the measure of how strong the RF signal is at the receiver. Signal strength can affect the reliability and performance of the wireless connection, as well as the data rate and throughput of the traffic. The higher the signal strength, the better the signal quality and the higher the data rate. The lower the signal strength, the worse the signal quality and the lower the data rate.
The data rate of an 802.11ac connection depends on several factors, such as channel bandwidth, modulation and coding scheme (MCS), spatial streams, guard interval, and beamforming. However, these factors are also influenced by the signal strength, as they require a certain signal-to-noise ratio (SNR) to operate properly.
SNR is the ratio of the signal strength to the noise floor, which is the measure of the background noise or interference in the RF environment. The higher the SNR, the more robust and efficient the communication.
The lower the SNR, the more prone and vulnerable to errors and retries.
According to the CWNA Official Study Guide , Table 3.7, page 112, an 802.11ac connection with a channel bandwidth of 80 MHz, an MCS of 9, two spatial streams, a short guard interval, and no beamforming can achieve a maximum data rate of 867 Mbps. However, this data rate requires a minimum SNR of 30 dB to maintain a sufficient signal quality. If the signal strength is -84 dBm and the noise floor is -96 dBm, then the SNR is only 12 dB (-84 dBm - (-96 dBm) = 12 dB), which is far below the required SNR for this data rate.
Therefore, the data rate will drop significantly to match the lower SNR and signal quality.
To solve this problem, the signal strength should be increased to improve the SNR and data rate. This can be done by adjusting the output power or channel assignment of the AP or client, relocating or reorienting some APs or antennas to reduce attenuation or interference, updating or replacing some faulty or outdated hardware or software components, etc. References: , Chapter 3, page 112; , Section 3.2


NEW QUESTION # 31
What can an impedance mismatch in the RF cables and connectors cause?

  • A. Fewer MCS values in the MCS table
  • B. Increased amplitude of the RF signal
  • C. Excessive VSWR
  • D. Increased range of the RF signal

Answer: C

Explanation:
VSWR stands for Voltage Standing Wave Ratio, which is a measure of how well the impedance of the RF cable and connectors matches the impedance of the transmitter and the antenna. Impedance is the opposition to the flow of alternating current in an RF circuit, and it depends on the frequency, resistance, capacitance, and inductance of the components. A perfect impedance match would have a VSWR of 1:1, meaning that all the power is transferred from the transmitter to the antenna, and none is reflected back. However, in reality, there is always some degree of mismatch, which causes some power to be reflected back to the transmitter, creating standing waves along the cable. This reduces the efficiency and performance of the wireless system, and can also damage the transmitter. Excessive VSWR can be caused by using poor quality or damaged cables and connectors, or by using components that have different impedance ratings123. References: CWNA-
109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 90; CWNA-109 Study Guide, Chapter 2:
Radio Frequency Fundamentals, page 86; CWNP website, CWNA Certification.


NEW QUESTION # 32
A client STA must choose the best AP for connectivity. As part of the evaluation, it must verify compatible data rates. What can the client STA use to verify that an AP supports the same data rates that it supports?

  • A. Probe request frames transmitted by other client STAs
  • B. Authentication frames transmitted by the other client STAs
  • C. Data frames sent between the AP and current clients STAs
  • D. Beacon frames transmitted by the AP

Answer: D

Explanation:
The client STA can use Beacon frames transmitted by the AP to verify that an AP supports the same data rates that it supports. Beacon frames are management frames that are periodically broadcasted by the APs to announce their presence, capabilities, and parameters. Oneof the information elements contained in the Beacon frames is the Supported Rates or Extended Supported Rates, which lists the data rates that the AP can use for communication. The client STA can compare its own data rates with those advertised by the AP to determine if they are compatible. Data frames, authentication frames, and probe request frames do not contain information about data rates. References: [CWNP Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 133; [CWNA: Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 123.


NEW QUESTION # 33
You are using a site survey tool for post-implementation validation. You have installed the appropriate adapter driver and imported a floor plan. Now, you want to take the next step in proper tool use. What must you do before gathering survey data after the floor plan is imported?

  • A. Install iPerf
  • B. Install WinPCAP
  • C. Calibrate the floor plan
  • D. Nothing, you can simply start capturing signal readings

Answer: C

Explanation:
Calibrating the floor plan is what you must do before gathering survey data after the floor plan is imported when using a site survey tool for post-implementation validation. A site survey tool is a software application that can run on a laptop, tablet, smartphone, or other device that has a Wi-Fi adapter and a GPS receiver. A site survey tool can scan the wireless environment and collect information about the detected access points and client stations, such as their SSID, BSSID, channel, signal strength, security, and data rate. A site survey tool can also measure and display various metrics of network performance, such as throughput, jitter, packet loss, delay, and SNR. A site survey tool can also use a floor plan to visualize the wirelesscoverage and quality in different locations on a map. A floor plan is an image file that shows the layout and dimensions of a building or an area where the WLAN is deployed. A floor plan can be imported from various sources, such as a CAD file, a PDF file, an image file, or a Google Maps screenshot. After importing a floor plan into a site survey tool, it is necessary to calibrate the floor plan before gathering survey data. Calibrating the floor plan means adjusting the scale and orientation of the floor plan to match the actual size and direction of the area.
Calibrating the floor plan can be done by using a reference point or a reference line that has a known distance or angle in the real world. Calibrating the floor plan ensures that the survey data is accurate and consistent with the physical environment. References: 1, Chapter 7, page 290; 2, Section 4.3


NEW QUESTION # 34
When compared with legacy Power Save mode, how does VHT TXOP power save improve battery life for devices on a WLAN?

  • A. Legacy Power Save mode was removed in the 802.11ac amendment.
  • B. VHT TXOP power save allows stations to enter sleep mode and legacy Power Save does not.
  • C. VHT TXOP power save allows the WLAN transceiver to disable more components when in a low power state.
  • D. VHT TXOP power save uses the partial AID in the preamble to allow clients to identify frames targeted for them.

Answer: C

Explanation:
VHT TXOP (Very High Throughput Transmit Opportunity) power save is a feature introduced with the 802.11ac amendment, which is designed to improve the power efficiency of devices connected to a WLAN. This feature enhances battery life in several ways, compared to the legacy Power Save mode:
Enhanced Power Saving: VHT TXOP power save allows devices to disable more components of the WLAN transceiver when they are in a low power state. This reduces the power consumption during periods when the device is not actively transmitting or receiving data. Intelligent Wake-Up Mechanisms: It employs more sophisticated mechanisms for devices to determine when they need to wake up and listen to the channel, further reducing unnecessary power usage.
Optimized Operation: This power save mode is optimized for the high-throughput environment of
802.11ac networks, allowing devices to efficiently manage power while maintaining high performance.
Legacy Power Save mode, introduced in earlier versions of the 802.11 standards, does not provide the same level of component disablement or the intelligent wake-up mechanisms found in VHT TXOP power save, making option B the correct answer.


NEW QUESTION # 35
You are troubleshooting a controller-based AP that is unable to locate the controller. DHCP is not use and the controller is located at 10.10.10.81/24 while the AP is on the 10.10.16.0/24 network. What should be inspected to verify proper configuration?

  • A. NTP
  • B. AP hosts file
  • C. DNS
  • D. BOOTH

Answer: C

Explanation:
What should be inspected to verify proper configuration is DNS. DNS stands for Domain Name System and is a service that resolves hostnames to IP addresses. In a controller-based AP deployment, DNS can be used to help the AP locate the controller by using a predefined hostname such as CISCO-CAPWAP-CONTROLLER or aruba-master. The AP sends a DNS query for this hostname and receives an IP address of the controller as a response. Therefore, if DNS is not configured properly or if there is no DNS entry for the controller hostname, the AP may not be able to locate the controller. NTP, BOOTP, and AP hosts file are not relevant for this scenario. References: [CWNP Certified Wireless Network Administrator Official Study Guide:
ExamCWNA-109], page 374; [CWNA: Certified Wireless Network Administrator Official Study Guide:
ExamCWNA-109], page 364.


NEW QUESTION # 36
What statement about 802.11 WLAN performance is true?

  • A. To get the best performance out of an AP, you should disable data rates of 72 Mbps and lower
  • B. In modem networks, both centralized and distributed data forwarding work well for most standard office deployments
  • C. In most WLANs, no special skill or tuning is required to get peak performance
  • D. WLANs perform better as more wireless clients connect with each AP

Answer: B

Explanation:
The statement that in modern networks, both centralized and distributed data forwarding work well for most standard office deployments is true about WLAN performance. Data forwarding refers to how wireless frames are transmitted from wireless clients to wired networks or vice versa through wireless access points (APs). Centralized data forwarding means that all wireless frames are sent to a central controller or gateway before being forwarded to their destinations.
Distributed data forwarding means that wireless frames are forwarded directly by the APs to their destinations without going through a central controller or gateway. Both methods have their advantages and disadvantages, depending on the network size, topology, traffic pattern, security, and management requirements. However, in modern networks, both methods can achieve high performance and scalability for most standard office deployments, as they can leverage advanced features such as fast roaming, load balancing, quality of service, and encryption. The other statements about WLAN performance are false. In most WLANs, special skill or tuning is required to get peak performance, such as selecting the appropriate channel, power, data rate, and antenna settings. WLANs perform worse as more wireless clients connect with each AP, as they cause more contention and interference on the wireless medium. To get the best performance out of an AP, you should not disable data rates of 72 Mbps and lower, as they are needed for backward compatibility and range extension.


NEW QUESTION # 37
What security solution is deprecated in the 802.11 standard and should never be used in any modern WLAN deployment?

  • A. CCMP
  • B. AES
  • C. Shared Key Authentication
  • D. Open System Authentication

Answer: C

Explanation:
Shared Key Authentication is a security solution that was defined in the original 802.11 standard as an alternative to Open System Authentication, which does not provide any security at all.
Shared Key Authentication uses WEP (Wired Equivalent Privacy) to encrypt and authenticate data frames between the client station and the AP. However, WEP has been proven to be extremely vulnerable to various attacks that can easily crack the encryption key and compromise the network security. Therefore, Shared Key Authentication is deprecated in the 802.11 standard and should never be used in any modern WLAN deployment.


NEW QUESTION # 38
What is the final step in an effective troubleshooting process?

  • A. Document the results
  • B. Notify the users of problem resolution
  • C. Disable the WLAN
  • D. Verify the solution

Answer: A

Explanation:
The final step in an effective troubleshooting process is to document the results. Documentation is essential for keeping track of the problem history, the actions taken, the solutions implemented, and the outcomes achieved. Documentation can also help to prevent future problems, improve best practices, and provide feedback for improvement. Documentation should include relevant information such as problem description, symptoms, root cause analysis, resolution steps, verification methods, and lessons learned. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-
109], page 513; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-
109], page 483.


NEW QUESTION # 39
What modulation and multiplexing technique, used by 802.11a/g/n/ac/ax, divides a wireless channel into multiple narrow, orthogonal subcarriers to transmit data in parallel?

  • A. FHSS
  • B. OFDM
  • C. DSSS
  • D. CCK

Answer: B

Explanation:
Orthogonal Frequency Division Multiplexing (OFDM) is a modulation technique that divides a wireless channel into many smaller, overlapping but mathematically orthogonal subcarriers. Data is transmitted in parallel across these subcarriers simultaneously, which improves spectral efficiency and provides resistance to multipath interference. OFDM was first used in WLANs by the 802.11a amendment and has remained the foundational modulation technique for 802.11g,
802.11n, 802.11ac, and 802.11ax (with the addition of OFDMA).


NEW QUESTION # 40
What is required when operating 802.11ax APS in the 6 GHz band using passphrase-based authentication?

  • A. HT PHY
  • B. CCMP
  • C. VHT PHY
  • D. SAE

Answer: D

Explanation:
SAE (Simultaneous Authentication of Equals) is required when operating 802.11ax APs in the 6 GHz band using passphrase-based authentication. SAE is a secure and robust authentication method that is defined in the IEEE 802.11s amendment and is also known as WPA3-Personal or WPA3-SAE. SAE is based on a cryptographic technique called Dragonfly Key Exchange, which allows two parties to establish a shared secret key using a passphrase, without revealing the passphrase or the key to an eavesdropper or an attacker. SAE also provides forward secrecy, which means that if the passphrase or the key is compromised in the future, it does not affect the security of past communications. SAE is required when operating 802.11ax APs in the 6 GHz band using passphrase-based authentication because of the new regulations and standards that apply to this band. The 6 GHz band is a new frequency band that was opened for unlicensed use by the FCC and other regulatory bodies in 2020. The 6 GHz band offers more spectrum and less interference than the existing 2.4 GHz and 5 GHz bands, which can enable higher performance and efficiency for Wi-Fi devices. However, the 6 GHz band also has some restrictions and requirements that are different from the other bands, such as:
The 6 GHz band is divided into two sub-bands: U-NII-5 (5925-6425 MHz) and U-NII-7 (6525-6875 MHz). The U-NII-5 sub-band is subject to DFS (Dynamic Frequency Selection) rules, which require Wi- Fi devices to monitor and avoid using channels that are occupied by radar systems or other primary users. The U-NII-7 sub-band is not subject to DFS rules, but it has a lower maximum transmit power limit than the U-NII-5 sub-band.
The Wi-Fi devices that operate in the 6 GHz band are called 6E devices, which stands for Extended Spectrum. 6E devices must support 802.11ax technology, which is also known as Wi-Fi
6 or High Efficiency (HE). 802.11ax is a new standard that improves the performance and efficiency of Wi-Fi networks by using features such as OFDMA (Orthogonal Frequency Division Multiple Access), MU- MIMO (Multi-User Multiple Input Multiple Output), BSS Coloring, TWT (Target Wake Time), and HE PHY and MAC enhancements.
The 6E devices that operate in the 6 GHz band must also support WPA3 security, which is a new security protocol that replaces WPA2 and provides stronger encryption and authentication for Wi- Fi networks. WPA3 has two modes: WPA3-Personal and WPA3-Enterprise. WPA3-Personal uses SAE as its authentication method, which requires a passphrase to establish a secure connection between two devices. WPA3-Enterprise uses EAP (Extensible Authentication Protocol) as its authentication method, which requires a certificate or a credential to authenticate with a server.
Therefore, SAE is required when operating 802.11ax APs in the 6 GHz band using passphrase- based authentication because it is part of WPA3-Personal security, which is mandatory for 6E devices in this band.


NEW QUESTION # 41
In a mesh BSS (MBSS), according to the 802.11 standard, what device connect the mesh to an Ethernet network?

  • A. Mesh Router
  • B. Mesh Gate
  • C. Mesh Portal
  • D. Mesh Switch

Answer: C

Explanation:
a mesh portal is a device that connects a mesh BSS (MBSS) to an Ethernet network, such as the Internet. A mesh portal acts as a bridge between the wired and wireless domains, and allows the mesh stations to communicate with external networks. A mesh portal is also a mesh point, which means it can forward traffic within the MBSS.
The other options are not correct. Option A. Mesh Gate is a device that connects a mesh BSS (MBSS) to another mesh BSS or another wireless network, such as an infrastructure BSS or an ad hoc network2. A mesh gate acts as a gateway between different wireless domains, and allows the mesh stations to communicate with other wireless networks. A mesh gate is also a mesh point, which means it can forward traffic within the MBSS. Option B. Mesh Switch is not a valid term in the 802.11 standard. Option C. Mesh Router is also not a valid term in the 802.11 standard.


NEW QUESTION # 42
You support a WLAN using dual-band 802.11ac three stream access points. All access points have both the 2.4 GHz and 5 GHz radios enabled and use 40 MHz channels in 5 GHz and 20 MHz channels in 2.4 GHz. A manager is concerned about the fact that each access point is connected using a 1 Gbps Ethernet link. He is concerned that the Ethernet link will not be able to handle the load from the wireless radios. What do you tell him?

  • A. Due to 802.11 network operations and the dynamic rates used by devices on the network, the two radios will likely not exceed the 1 Gpbs Ethernet link.
  • B. His concern is invalid because the AP will compress all data before transmitting it onto the Ethernet link.
  • C. His concern is valid and the company should immediately plan to run a second 1 Gbps Ethernet link to each AP.
  • D. His concern is valid and the company should upgrade all Ethernet links to 10 Gbps immediately.

Answer: A

Explanation:
What you should tell him is that due to 802.11 network operations and the dynamic rates used by devices on the network, the two radios will likely not exceed the 1 Gbps Ethernet link. This is because the actual throughput of an 802.11 network is much lower than the theoretical data rates due to factors such as overhead, contention, interference, retransmissions, and environmental conditions. Moreover, the data rates used by devices on the network vary depending on their distance, signal quality, capabilities, and configuration. Therefore, it is unlikely that both radios of the AP will simultaneously use the maximum data rates and saturate the 1 Gbps Ethernet link.
Upgrading to a 10 Gbps Ethernet link or running a second 1 Gbps Ethernet link may be unnecessary and costly. Compressing all data before transmitting it onto the Ethernet link may introduce additional overhead and latency.


NEW QUESTION # 43
You are deploying a WLAN monitoring solution that utilizes distributed sensor devices. Where should sensors be deployed for best results? Choose the single best answer.

  • A. In switching closets
  • B. Above the plenum on each floor
  • C. Every 5 meters and alongside each AP
  • D. In critical areas where WLAN performance must be high

Answer: D

Explanation:
Sensors should be deployed in critical areas where WLAN performance must be high for best results when using a WLAN monitoring solution that utilizes distributed sensor devices. A WLAN monitoring solution is a system that collects, analyzes, and reports on the status and performance of a WLAN. A WLAN monitoring solution can use different methods to gather data from the WLAN, such as embedded software agents, external hardware probes, or distributed sensor devices. Distributed sensor devices are dedicated devices that are deployed throughout the WLAN coverage area to monitor the wireless traffic and environment. Distributed sensor devices can perform various functions, such as scanning the spectrum, capturing wireless frames, measuring signal quality, detecting rogue access points, testing connectivity, and generating alerts. Distributed sensor devices can provide more accurate and comprehensive data than other methods, but they also require more planning and deployment costs. Therefore, it is important to deploy sensors strategically in critical areas where WLAN performance must be high, such as high-density zones, high-priority applications, or high-security locations. By deploying sensors in critical areas, the WLAN monitoring solution can ensure optimal WLAN performance and reliability in those areas and identify and resolve any issues or problems that may arise. The other options are not the best places to deploy sensors for best results. Deploying sensors in switching closets is not effective because sensors need to be close to the wireless medium to monitor it properly. Deploying sensors every 5 meters and alongside each AP is not efficient because sensors may overlap or interfere with each other and cause unnecessary redundancy or complexity. Deploying sensors above the plenum oneach floor is not practical because sensors may not capture the wireless traffic and environment accurately due to attenuation or reflection from the ceiling materials or objects. References: CWNA-109 Study Guide, Chapter 14: Troubleshooting Wireless LANs, page 4831


NEW QUESTION # 44
......

Authentic Best resources for CWNA-109 Online Practice Exam: https://www.actual4test.com/CWNA-109_examcollection.html

Updates Up to 365 days On Developing CWNA-109 Braindumps: https://drive.google.com/open?id=1-dtNgR059qH_2s_qU0XLB34ueYz9lE-8