Jan 15, 2023 Newest HPE0-J58 Exam Dumps – Achieve Success in Actual HPE0-J58 Exam
Updated HP HPE0-J58 Dumps – Check Free HPE0-J58 Exam Dumps (2023)
NEW QUESTION 16
A customer needs to replicate data from a single HPE 3PAR source array to multiple HPE SPAR target arrays. What is required to support a 3:1 fan-out for Remote Copy?
- A. 4-port 16 Gb Fibre Channel Adapters
- B. a 4-node HPE 3PAR array
- C. HPE 3PAR 20000
- D. HPE SN4000B SAN Extension switches
Answer: B
NEW QUESTION 17
A customer has two sites within a short distance. They require a primary storage solution which supports automatic failover for their block storage, SMB shares, and NFS home directories. Which HPE solution best fits the customer's requirements?
- A. HPE Nimble
- B. HPE StoreOnce
- C. HPE Simplivity
- D. HPE 3PAR
Answer: D
NEW QUESTION 18
A customer deployed an HPE 3PAR 8200 and an HPE 3PAR 8400 array Peer persistence is configured between them All remote copy links are lost, Out connection to the Quorum witness is maintained by Doth arrays.
Immediately after the remote copy links are restored, the customer reports they cannot perform a manual switchover for maintenance in SSMC
What is causing this issue'
- A. Manual switchover is not supported between arrays of different models
- B. A manual switchover cannot be performed until the volumes are resynced.
- C. Manual switchover cannot be performed if the arrays are running different firmware versions
- D. Peer Persistence is designed for Automatic Transparent Failover and must be disabled to perform a manual switchover.
Answer: D
NEW QUESTION 19
A customer wants to implement a disaster recovery plan for their current HPE 3PAR array dat A.
They have obtained a remote site 10km away their primary site. They have performed bandwidth testing,
and have confirmed their RTT is approximately 100ms. The customer needs to provide data replication to assure the best data availability they can achieve.
Which synchronization method meets their needs?
- A. Synchronous Remote Copy
- B. Asynchronous Streaming
- C. Peer Persistence
- D. Asynchronous Periodic Remote Copy
Answer: D
NEW QUESTION 20
A customer needs to replicate multiple HPE 3PAR source arrays to a single HPE 3PAR target array at a Disaster Recovery sue.
What is required to support a 31 fan-in for Remote Copy?
- A. HPE SN4000B SAN Extension Switches
- B. 4-poit 16 Go Fibre Channel Adapters
- C. HPE 3PAR 2OO00
- D. a 4-node HPE 3PAR array
Answer: B
NEW QUESTION 21
A customer's environment has.
* one HPE 3PAR 9000 series funning OS 3.3.1. direct-connected to a single host
* two HPE 3PAR 20000 series fc arrays recently upgraded to OS 3.2.2
The customer recently purchased a third HPE 3PAR 20000 series fc array running OS 3.2.2 and wants to incorporate all four as Storage Federation members.
What should you do before implementing Storage Federation?
- A. Upgrade arrays to match highest OS version
- B. Change Direct connection to FC-based array
- C. Decommission the HPE 9000 series array.
- D. Install a Peer Motion License only on the 20000 series array.
Answer: C
NEW QUESTION 22
Refer to the exhibit.
A customer requests a solution for two 3PAR 8450 storage arrays using synchronous replication. The customer wants the array configured to...
A junior architect you are coaching created the configuration shown for each array
What should you add to me configuration for each array to meet customer performance requirements?
- A. 32 additional SSD drives
- B. 4 additional disk enclosures
- C. 1 additional pair of nodes
- D. SAS bus multiplexers
Answer: C
NEW QUESTION 23
You are starting an assessment to design a new multi-storage environment for a customer. You have collected data on all the current arrays using SAF collector.
What should be the next step in your design process?
- A. Open the .zip file with NinjaSTARS
- B. Import the .zip file into OCA
- C. Upload the .zip file to the SAF Portal
- D. Send the .zip file to [email protected]
Answer: A
NEW QUESTION 24
A customer's primary and OR datacenter are over 700 km apart. The customer wants to minimize data loss during a OR failover, but is worried about the potential production IO performance impact of replicating their data.
You recommend HPE 3PAR asynchronous replication.
Which key factor should you explain about the proposed solution?
- A. Host writes are acknowledged as soon as they are performed on the primary storage array
- B. All writes are written to the target
- C. Host write latencies win increase
- D. Most writes are acknowledged as soon as they are performed on both the primary and secondary storage array
Answer: A
NEW QUESTION 25
A customer requires an all-flash solution that will scale out, with multiple arrays for replication. The customer
also needs the solution to provide more data per terabyte of flash storage than competing solutions.
Which HPE program should you leverage in your solution to help meet the customer's requirements?
- A. HPE Store More Guarantee
- B. HPE Get 6-Nines Guarantee
- C. HPE Get Thin Guarantee
- D. HPE Nimble Timeless Storage
Answer: A
NEW QUESTION 26
A customer has two data centers in a metropolitan areA. The link between the data centers is IP-based and satisfies the bandwidth and latency requirements. They have the following requirements:
* Transparently and automatically failover and fall back between sites
* Provide block and file access
* Block access must provide connectivity for fibre channel and iSCSi hosts
* All-Flash storage solution
You plan to propose a design based on HPE 3PAR storage arrays.
What would be the most cost-effective model that meets the customer needs?
- A. HPE 3PAR 8450
- B. HPE 3PAR 20850
- C. HPE 3PAR 20450
- D. HPE 3PAR 9450
Answer: A
NEW QUESTION 27
A customer has two HPE SPAR arrays with synchronous replication configured.
I he customer established a new location less than 10 km away that will he used for disaster recovery. The data at the disaster location does not need to be as currant as the data at the primary location. The link between the two locations is not reliable during the daytime due to snared bandwidth
which replication should you recommend to meet this customer's needs?
- A. Asynchronous Streaming
- B. Asynchronous Periodic
- C. Synchronous
- D. 3DC Peer Persistence
Answer: B
NEW QUESTION 28
A customer configured the RCIP ports on two HPE 3PAR arrays, and cabled them to the respective networks.
The remote copy links between the arrays are established, and the remote copy service Is started successfully.
The customer wants to ensure they have a latency lower than 5 ms and can support a throughput of 8 Gb/s.
What should you do to verify the links are correctly sized to support the replication bandwidth required?
- A. Ask the network administrator to check the latency
- B. Use the checkrclink command from the 3PAR CLI.
- C. Use the relink status check from the 3PAR SSMC
- D. Check the relink statistics reported in InfoSight
Answer: B
NEW QUESTION 29
Refer to the exhibit.
A customer is considering a new HPE 3PAR for the purpose of implementing deduplication and compression.
Based on the output returned from the NinjaCrawler tool, what do you know about the customer data?
- A. This data has a block size which is not optimal for HPE 3PAR
- B. This data has a video data workload profile
- C. This data is from an HP-UX system
- D. This data is a good candidate for HPE 3PAR deduplication
Answer: C
NEW QUESTION 30
A customer has a requirement to provide Disaster Recovery for an application that is very sensitive to IO
latency.
The customer has specified an RPO of less than 3 minutes for this application.
How can HPE 3PAR Remote Copy help meet the customers specified requirements?
- A. by using Asynchronous Streaming Replication
- B. by using Synchronous Replication
- C. by using Periodic Asynchronous Replication with an interval of 3 mins
- D. by using Synchronous Long Distance Mode
Answer: A
NEW QUESTION 31
A customer is expecting rapid growth of their data storage needs on their HPE Nimble arrays. Which HPE tool should you recommend to best assist with capacity planning?
- A. NinjaCrawler
- B. NinjaStars for Nimble
- C. One Config Advanced
- D. InfoSight
Answer: C
NEW QUESTION 32
A customer has two HPE Nimble arrays that are replication partners. The customer suffers a complete outage on the source array. What does the administrator need to do to make the most recent snapshot available?
- A. Promote the target snapshot
- B. Perform a handover between the arrays
- C. Verify the automatic failover occurred
- D. Demote the source snapshot
Answer: B
NEW QUESTION 33
Refer to the exhibit.
A customer requests a quote for an HPE 3PAR 9450 array. The customer will provision a single CPG using RAID 6 (6+2) arx1 require cage availability
What must De changed in the Bin of Materials shown to meet this requirement?
- A. Add an additional HPE 3PAR StoreServ File Controller v3 System
- B. Add A HPE 3PAR 9000 24-disk 2U SFF (2 Sin) SAS Delve Enclosures.
- C. Remove 2 HPE 3PAR 9000 2-port to GD Ethernet Host Pus Adapters.
- D. Change From Direct Connect to Daisy-chain cabling
Answer: A
NEW QUESTION 34
A customer has a two-node HPE 3PAR array with three additional drive enclosures. There is a single CPG setup for RAID 5 (3+1). One of the drive enclosures has failed and must be replaced.
What needs to be considered before starling the repair?
- A. The enclosure I'O modules will need to be paired with the replacement enclosure
- B. The array must be powered down to perform the enclosure replacement.
- C. HA cage availably will be lost during the enclosure replacement process.
- D. A node rescue will need to be performed after the enclosure replacement.
Answer: C
NEW QUESTION 35
You are presenting a Remote Copy solution to a customer that expects to experience significant future growth During your presentation, the customer expresses concerns about future integrations of HPE 3PAR arrays into the replication solution.
How should you respond to address the customer concern?
- A. HPE 3PAR 8000 arrays can only replicate to other HPE 3PAR 8000 and HPE 3PAR 7000 arrays.
- B. Asynchronous Streaming replication is available on all generations of HPE 3PAR arrays.
- C. Only HPE 3PAR 20000 arrays can be a replication target for 8000. 9000, and 20000 arrays.
- D. All current and previous generation HPE 3PAR arrays can replicate data between each other
Answer: D
NEW QUESTION 36
......
Actual HPE0-J58 Exam Recently Updated Questions with Free Demo: https://www.actual4test.com/HPE0-J58_examcollection.html
Valid HPE0-J58 exam with HP Real Exam Questions: https://drive.google.com/open?id=1iHpKLi-G076UD9irE9Q7NmI9UZoRWul0